Easier up and down, with your wheelchairs.




    Hydraulic wheelchair lift Pictures

    Wheelchair lift is a type of vertical transportation system used to move the old people or the disabled between different floors of a building; The platform is driven up by piston and down by its weight, the user cannot open for door during lift working, it provides a much more safety and convenient up and down solutions for those persons.

    1. Automatic ramp: 75°ramp Range and prevent the wheelchair outside
    2. Safety control voltage: All the button and operation parts use DC 24V safety voltage, keep users’safety
    3. Platform lock: Lock the platform in case of any mis-operation by the children or strangers.
    4. Emergency Stop: The lift can be stopped immediately in case of any emergency
    5. Emergency Lowering: The platform can be lowered by manual down button in case of power failure
    6. Emergency limit switch: Keep the lift working as normal in case of the up limit switch broken.
    7. Over-current protection: The lift will stop working once over current to protect the motor
    8. IP66 electrical parts: Protect from the rain or wet weather, suitable for out use
    9. Standardized components: Replaceable in time for all lifetime, never worry about broken parts
    10. Safety Sensor under platform: The lift will be stopped immediately if the bottom meets any obstacles when going down, especially to protect the children if he enter accidentally.
    11. Mechanical anti-falling device: The device will lock the lift within 0.15S and keep it in its position if the chain was cut off, assure the users’safety in case of any emergency
    1. Make sure the platform door and landing door are closed if they are installed already.
    2. Make the the ‘E-stop’button on the calling post and platform are released
    3. The user can enter onto the platform and lock the wheelchair brake, close the platform door(if installed).
    4. Turn on the power switch on the control panel and indicator light.
    5. Press the ‘Up’ button, platform raises; press the ‘Down’button, platform will descend.
    6. Press the red ‘Stop’ button in case of any emergency

    Regular maintenance aims to carry out comprehensive inspection, repair, replacement and adjustment of some parts of the product in operation in accordance with relevant standards so as to ensure product quality fundamentally.

    1. Protective measures for the product aim to ensure perfect operation of the facilities and appropriate lubrication to moving parts.
    2. Proceed with trial run of lifting table top for one time to make sure that it is free of any shaking and abnormal noise and vibration during operation.
    3. All buttons and indicator lights have normal appearance and perfect contact, which should be flexible and free of any defect. All indicator lights must be normal in operation.
    4. Motor should be clean and free of any dust and oil contaminant, which should be free of any abnormal noise during operation. The temperature rise should be normal without any odor.
    5. Main contact and relay should be normal in operation, which should be free of any abnormal noise, odor and overheat.
    6. Check if all bolts fixed to various parts are properly tightened.
    7. Clean off impurities inside the silos (if available).
    8. Upper and lower limit switches should be normal in operation; roller should be flexible in rotation, and must be properly positioned.
    9. Check if coupling shaft, bearing, oil cylinder pin shaft and arm support cardinal axis are in good condition.
    10. Hydraulic oil should be free of any pollution, and the oil level should be appropriate. Hydraulic oil should top over the tank bottom by 40-50mm when the hoist is at the maximum height. Replace the hydraulic oil in time if it becomes dark and glutinous or contains such impurities as gravel (32# hydraulic oil).
    11. Any part must be provided with splice mark in case of disassembly. The assembly interface must be clean and smooth. All screws and nuts must be properly tightened. Otherwise, they may affect lifting stability of the platform to the extent of incurring shake.
    12. Check hydraulic pipeline to make sure that the pipeline is free of any damage, and the joint is firmly fixed. All joints must be tightened to guard against oil leakage.
    13. Hydraulic oil must be thoroughly discharged in case of replacement fresh hydraulic oil.
    Tighten the joint, and take out the oil filter for cleaning before blowing it with compressed air. After that, put the oil filter back to the oil tank, and properly connect the pipeline (replace used hydraulic oil with fresh one. Otherwise, it may accelerate the wearing to the moving parts in the hydraulic hoist system).
    14. During normal operation, vehicle battery should be used only on condition that it is fully charged. The battery must be charged every three months during storage, which shall not be used inside the enclosed vessel or nearby the fire source (for DC type).
    15. Use brush or dry cloth to eliminate incrustation inside each part. Rinse with liquid detergent is strictly prohibited.

    Standard Features

    Standard configuration comes with lift
    Manual Down
    Lift Panel
    Connection Point
    Calling Button
    Fix Point
    wheelchair lift lock
    Lift Lock

    Upgraded Options

    To suit for different site, Nostec lift provide different entrance&exit direction, through type, 90 degree or singe side opening are available, platform door and landing door are also for choice.

    Standard model list for reference

    Highly recommended PWD lift models for the users

    Max Platform Height1200160020002400280032003600+400…6000
    Stops2
    Lift capacity250kg
    Speed70mm/s
    Platform size1430*900mm
    Dimension1430mm(Not include ramp size)*1260mm(W)* (H+850) mm
    Access direction180°in and out
    Ramp angle75°
    Control waysPlatform control, post control, remote control
    Mode of MotionHold-to-run control
    ColorStandard white, powder coating
    MaterialT6 series aluminum alloy
    Drive modeHydraulic cylinder+ Chain
    Control modePLC control
    Control voltage24V DC
    Voltage220V/50HZ/1 phase, 10A
    Motor Power1.5kw
    Pump flow98ML/S
    Working pressure10MPa
    Hydraulic tank capacity8L(Height ≤3.2m); 15L(Height>3.2m)
    Hydraulic oil type32#

    Wheelchair lift applications

    PWD lift is very suitable for both indoors and outdoors use, such as homes, commercial buildings, places of worship, and schools, which is very useful for helping a wheelchair user travel between levels.

    Lift cabin

    Lift cabin is also available, which can be also ground mounted directly, used as home lift, suit for villa, basement, homes, both in door and outdoor.

    Safety Devices

    Automatic ramp

    75°ramp Range and prevent the wheelchair outside

    Safety control voltage

    All the button and operation parts use DC 24V safety voltage, keep users’ safety

    Platform lock

    Lock the platform in case of any mis-operation by the children or strangers.

    Emergency Stop

    The lift can be stopped immediately in case of any emergency

    Emergency Lowering

    The platform can be lowered by manual down button in case of power failure

    Emergency limit switch

    Keep the lift working as normal in case of the up limit switch broken.

    Electromagnet

    Both the platform door and landing door cannot be open during the lift working

    Standardized components

    Replaceable in time for all lifetime, never worry about broken parts

    Safety Sensor under platform

    The lift will be stopped immediately if the bottom meets any obstacles when going down, especially to protect the children if he enter accidentally.

    Mechanical anti-falling device

    The device will lock the lift within 0.15S and keep it in its position if the chain was cut off, assure the users’ safety in case of any emergency

    Video speaks more

    Please check the video below to know more about the hydraulic vertical lift platform.




      Scroll to Top